List of Figures

| Table of Contents | List of Figures | List of Tables |

Figure 1. Sources of Additional Information About Origin200

Figure 1-1. Two-Module Origin200 System, Front View

Figure 1-2. Two-Module Origin200 and Origin200 GIGAchannel Systems, Rear View

Figure 1-3. Two-Module Origin200 Server in a Rack

Figure 1-4. Logical Block Diagram of an Origin200 Server

Figure 1-5. Logical Block Diagram of an Origin200 GIGAchannel Server

Figure 1-6. Logic Carrier

Figure 1-7. Main System Board and CPU Daughtercard

Figure 1-8. PCI Backplane and Slot IDs in a CPU Module

Figure 1-9. Layout of DIMM Sockets on the Origin200 Main System Board

Figure 1-10. Origin200 5.25-inch Peripheral Carrier and Drive Bay

Figure 1-11. Origin200 3.5-inch Drive, Sled, and Bay

Figure 1-12. Origin200 GIGAchannel XIO Connectors

Figure 1-13. GIGAchannel Expansion Cabinet (Rear View) and XIO Connector Locations

Figure 1-14. Origin200 GIGAchannel XIO Cable Connections

Figure 1-15. Origin200 GIGAchannel Cabling for Loopback Mode (No GIGAchannel Expansion Installed)

Figure 1-16. Air Flow Through the Origin200 CPU Module

Figure 1-17. Locations and Numbering of Fans in the Origin200 CPU Module

Figure 1-18. Air Flow and Blower Location in the GIGAchannel Expansion Chassis

Figure 2-1. Origin200 and Origin200 GIGAchannel Power and Grounding (Earthing) Overview

Figure 2-2. Minimum Clearances for the Origin200 Server, Tower Configuration

Figure 2-3. Items Included With the Origin200 Server, Tower Configuration

Figure 2-4. Basic Items Included With the Origin200 Server, Rackmountable Configuration

Figure 2-5. Basic Items Included With an Origin200 GIGAchannel Server, Tower Configuration

Figure 2-6. Basic Items Included With an Origin200 GIGAchannel Server, Rackmount Configuration

Figure 2-7. Origin200 CPU Module Connectors

Figure 2-8. Removing the Side Panel of the Second (Slave) Module

Figure 2-9. Removing the Module System Controller (MSC) Access Plate

Figure 2-10. MSC DIP Switch Location and Settings

Figure 2-11. Attaching a Grounding Cable Between a GIGAchannel Expansion Cabinet and a CPU Module

Figure 2-12. Attaching the XIO Cables Between a GIGAchannel Cabinet and a CPU Module

Figure 2-13. SCSI Drive ID Numbering for 3.5-Inch Drives in the Origin200 Server

Figure 2-14. Installing 3.5-Inch Drives in the Origin200 Server

Figure 2-15. Removing the Front Door of a CPU Module, Tower Configuration

Figure 2-16. Removing the Front Door, Rackmount Configuration

Figure 2-17. Removing the 5.25-Inch Peripheral Carrier

Figure 2-18. Removing a Blanking Plate and the Rear Access Plate From the Peripheral Carrier

Figure 2-19. Inserting a 5.25-Inch Drive in the Peripheral Carrier

Figure 2-20. Attaching a Power Connector to a 5.25-inch Drive

Figure 2-21. Attaching the SCSI Cable to a 5.25-Inch Drive

Figure 2-22. Replacing the Rear Access Plate on the Peripheral Carrier

Figure 2-23. Replacing the 5.25-Inch Peripheral Carrier

Figure 2-24. Attaching an Ethernet Networking Cable to an Origin200 Module

Figure 2-25. Attaching the Serial Cable

Figure 2-26. Attaching the Grounding and CrayLink Cables

Figure 2-27. Turning On the Master Power Switch

Figure 2-28. Turning On the Front Power Switch

Figure 3-1. Placing the Origin200 on a Work Surface

Figure 3-2. Origin200 Rackmounting Ears

Figure 3-3. Attaching the Rackmounting Hardware (Ears)

Figure 3-4. Installing the Rackmounting Shelf

Figure 3-5. Lifting the Origin200 Server Into a Rack

Figure 3-6. Attaching the Plastic End Caps to a Rackmounted Server

Figure 4-1. Origin200 Front Panel

Figure 4-2. Turning On the Master Power Switch (CPU Module Shown)

Figure 4-3. Turning On the Front Power Switch

Figure 4-4. Turning Off the Front Power Switch

Figure 4-5. Turning Off the Master Power Switch

Figure 4-6. Running an Origin200 GIGAchannel Without the GIGAchannelExpansion Cabinet (Loopback Mode)

Figure 4-7. Attaching a Serial Cable to Port 1 of the Origin200 Server

Figure 4-8. Location of the AUX Port

Figure 4-9. Example /hw Filesystem

Figure 5-1. Locking the Chassis With the Locking Tabs

Figure 5-2. Adjusting the Feet

Figure 5-3. Cosmetic Grill on the GIGAchannel Expansion Chassis

Figure 5-4. Removing the Front Door, Tower Configuration

Figure 5-5. Removing the Front Door, Rackmount Configuration

Figure 5-6. Removing the System Cover, Tower Origin200 System

Figure 5-7. Opening the Chassis Access Door, Tower Origin200 System

Figure 5-8. Removing the Top Cap

Figure 5-9. Removing the Lower Bezel

Figure 5-10. Removing the Pedestal Assembly (Feet)

Figure 6-1. Location of the 5.25-Inch Drive Bay

Figure 6-2. Removing the 5.25-Inch Peripheral Carrier

Figure 6-3. Removing a Blanking Plate and the Rear Access Plate From the Peripheral Carrier

Figure 6-4. Installing a 5.25-Inch Drive in the Peripheral Carrier

Figure 6-5. Replacing the 5.25-Inch Peripheral Carrier

Figure 6-6. Removing the Peripheral Carrier

Figure 6-7. Removing the Rear Access Plate From the Peripheral Carrier

Figure 6-8. Removing a Drive From the Peripheral Carrier

Figure 6-9. Replacing the Front Blanking Plate and Rear Access Plate

Figure 6-10. Replacing the 5.25-Inch Peripheral Carrier

Figure 6-11. 3.5-Inch Drive Bay and Correspondence of SCSI IDs to Drive Slots

Figure 6-12. Example 3.5-Inch Drive Slot Blanking Plate

Figure 6-13. Opening the Front Door of the Origin200 System

Figure 6-14. 3.5-Inch Drives Numbering in an Origin200 System

Figure 6-15. Installing a 3.5-Inch Peripheral in an Origin200 System

Figure 6-16. Opening the Front Door of an Origin200 System

Figure 6-17. 3.5-Inch Drives Numbering in an Origin200 System

Figure 6-18. Removing a 3.5-Inch Drive From an Origin200 Server

Figure 6-19. Location of the Serial Port Connectors on an Origin200 System

Figure A-1. Origin200 Serial Port Pinout Assignments

Figure A-2. Origin200 Parallel Port Pinout Assignments

Figure A-3. Origin200 Ethernet 10-Base-T/100-Base-TX Port Pinout Assignments

Figure A-4. Origin200 AUX Port Pinout Assignments