CHALLENGE™ S Server Owner's Guide
Prev		Next

List of Figures

Figure 1-1. Sources of Information for the Challenge S Server
Figure 1-2. Documentation
Figure 2-1. Challenge S, External View, Front
Figure 2-2. Challenge S, External View, Rear
Figure 2-3. Challenge S Front-Panel Controls
Figure 2-4. Challenge S Back-Panel Connectors
Figure 2-5. Challenge S Power Supply
Figure 2-6. Example Drive Release Button
Figure 2-7. Challenge S System Boards and GIO Slot Numbers
Figure 2-8. A Block Diagram of the MC1 ASIC
Figure 2-9. SIMM Bank and Slot Arrangement
Figure 2-10. Memory Block on the Challenge S System Board
Figure 2-11. ISDN Interface Architecture
Figure 3-1. Challenge S Back-Panel Connectors
Figure 3-2. Connecting the System Console (ASCII Terminal)
Figure 3-3. Connecting an Ethernet AUI Cable to the Challenge S Server
Figure 3-4. Ethernet AUI cable
Figure 3-5. Connecting an Ethernet 10-BASE T Cable to the Challenge S Server
Figure 3-6. Connecting an ISDN Cable to the Challenge S Server
Figure 3-7. The Challenge S Server Control Buttons on the Front Panel
Figure 3-8. Turning On the Challenge S Server
Figure 3-9. Turning Off the Challenge S Server
Figure 3-10. Removing the Top Cover From the Challenge S Server
Figure 3-11. Replacing the Top Cover on the Challenge S Server
Figure 3-12. Attaching a Lock to the Challenge S Server
Figure 4-1. Locating the SIMM Sockets
Figure 4-2. SIMM Bank and Socket Numbers
Figure 4-3. Orienting the SIMM
Figure 4-4. Tilting the SIMM Up to a Vertical Position
Figure 5-1. Locating the GIO Board Connectors (IOPLUS Board Shown)
Figure 5-2. Removing the Screw From the GIO I/O Port Face Plate
Figure 5-3. Inserting the GIO Board's I/O Connector Through the Backplane
Figure 5-4. Installing a Single-Width GIO Option Board
Figure 6-1. Locating the Drive Bracket Above the System Disk
Figure 6-2. Removing an Internal Drive Bracket
Figure 6-3. Power Cable to a Second Drive (Floptical Shown)
Figure 6-4. Installing a Second Drive Above the System Disk
Figure 6-5. Removing the 50-Pin SCSI Terminator From the Challenge S Server
Figure 6-6. Connecting an External 50-Pin SCSI Device to the Challenge S Server
Figure 6-7. Daisy-Chaining an External 50-Pin Single-Ended SCSI Device
Figure 6-8. Connecting a Terminator to the Last SCSI Device on the Chain
Figure 6-9. Connecting the Power Cable to an External Device
Figure 6-10. Serial Ports on the Rear of the Challenge S Server
Figure 6-11. Connecting the Serial Cable to the Serial Port
Figure 8-1. Pressing the Reset Button
Figure 8-2. Locating the Password Jumper
Figure 9-1. Part Number Locations for Standard System Components
Figure 9-2. Part Number Locations for Optional Components
Figure 9-3. Double-Sided Hex Wrench (4.5 mm and 3/16")
Figure 9-4. Locating the GIO Option Board
Figure 9-5. Removing the Screw From the Connector on the Rear of the Server
Figure 9-6. Removing the Screws From the GIO Option Board
Figure 9-7. Locating the IOPLUS Board With a GIO Option Board Installed
Figure 9-8. Removing the Screws From the IOPLUS Board's I/O Connector
Figure 9-9. Removing the Screws From an IOPLUS
Figure 9-10. Disconnecting the IOPLUS Board From the System Board
Figure 9-11. Locating the CPU Module
Figure 9-12. Removing the Two Screws From the CPU Module
Figure 9-13. Disconnecting the CPU Module
Figure 9-14. Installing the CPU Module
Figure 9-15. Locating the SIMMs
Figure 9-16. SIMM Socket and Bank Numbers
Figure 9-17. Releasing the Latches on the SIMM
Figure 9-18. GIO Board Installed in Slot 0
Figure 9-19. Locating the Floptical or Second Hard Disk Drive
Figure 9-20. Removing the Floptical Drive
Figure 9-21. Disconnecting the Power and SCSI Cables From the Floptical Drive
Figure 9-22. Locating a Floptical or Second Disk Drive Installed in the Top Slot
Figure 9-23. Disconnecting the Cables From the Floptical Disk Drive
Figure 9-24. Removing the System Disk Drive
Figure 9-25. Disconnecting the Power and SCSI Cables From the System Disk Drive
Figure 9-26. Installing the Replacement System Disk Drive
Figure 9-27. Reinstalling the Floptical Drive
Figure 9-28. Locating the Power Supply
Figure 9-29. Removing the Power Supply
Figure 9-30. Installing the Power Supply
Figure 10-1. Basic Parameters of Visual Display Terminal Workstation Adjustment (Adapted From ANSI/HFS 100-1988)
Figure A-1. MINIDIN8 Serial Port (RS-232) Pinout Numbering
Figure A-2. Parallel Port Pinout Numbering
Figure A-3. Ethernet 10-BASE T Pinout Numbering
Figure A-4. ISDN Pinout Numbering
Figure A-5. Ethernet AUI Pinout Numbering
Figure A-6. 50-Pin SCSI (High-Density) Pinout Numbering
Figure A-7. 68-Pin SCSI (High-Density) Pinout Numbering
Figure C-1. Floptical Drive Set to SCSI Address 2

Prev		Next
CHALLENGE™ S Server Owner's Guide		Chapter 1. Introduction